BuiltInFailures.StairRampFailures
Failures about StairRamp.
Inheritance Hierarchy
System.Object
Autodesk.Revit.DB.BuiltInFailures.StairRampFailures
Namespace: Autodesk.Revit.DB
Assembly: RevitAPI (in RevitAPI.dll) Version: 25.0.0.0 (25.0.0.0)
Syntax
public static class StairRampFailuresThe BuiltInFailures.StairRampFailures type exposes the following members.
Properties
Name
Description
Public Property
Static Member
ActualRiserHeightChanged
The actual riser height for one or more stairs violates the maximum set in the type.
Public Property
Static Member
AntiparallelRampRisers
Riser lines are parallel but not collinear. Can’t build Run between these Risers.
Public Property
Static Member
AntiparallelRampRisersError
Riser lines are parallel but not collinear. Can’t build Run between these Risers.
Public Property
Static Member
ArcRunRadiusTooSmall
Can’t create Run. Run radius is too small.
Public Property
Static Member
ArcRunWidthTooLongFailure
Arc run width is too long.
Public Property
Static Member
AutomaticLandingConvertedToSketchedLandingWarning
Some run(s) are deleted, so automatic landing is converted to sketched landing.
Public Property
Static Member
BadBalustersPerTread
Number of Balusters per Tread must be an integer greater than zero.
Public Property
Static Member
BadFillingSpacing
Spacing for Excess Length Fill is too small.
Public Property
Static Member
BadRailings
Can’t create Railings.
Public Property
Static Member
BadRailingsError
Can’t create Railings.
Public Property
Static Member
BadRailProfile
One or more Profile Loops are invalid, probably because of self-intersection.
Public Property
Static Member
BadTreadRiserProfile
Tread/Riser profile is invalid.
Public Property
Static Member
BalustersTooClose
Baluster Separation must be equal to or greater than the Baluster widths.
Public Property
Static Member
BalustersTooCloseAbsolute
Baluster Separation is too small.
Public Property
Static Member
BalusterUpsideDown
Top reference is below Bottom reference for one or more Balusters. These Balusters are not created.
Public Property
Static Member
CannotAlignSupportOnPosts
Cannot align the support on the posts.
Public Property
Static Member
CannotComputeRailElevation
Can’t compute elevation profile for one or more Rails
Public Property
Static Member
CannotCreateBaluster
Can’t create Balusters for given Width and Height.
Public Property
Static Member
CannotCreateBalusterPatterns
Can’t create Baluster Patterns for Railings
Public Property
Static Member
CannotCreateCornerBalusters
Can’t create corner Baluster
Public Property
Static Member
CannotCreateLandingStringer
Can’t create stringer at landing.
Public Property
Static Member
CannotCreateMiddleStringer
Can’t create one or more Middle Stringers.
Public Property
Static Member
CannotCreateMonolithicStairs
Can’t make monolithic Stairs.
Public Property
Static Member
CannotCreateNosing
Can’t create nosing on one or more treads.
Public Property
Static Member
CannotCreateOneOrMoreBaluster
Can’t create one or more Balusters
Public Property
Static Member
CannotCreateOneOrMoreTreads
Can’t create geometry for one or more treads.
Public Property
Static Member
CannotCreateOpenMiddleStringers
Can’t cut open/middle stringers geometry.
Public Property
Static Member
CannotCreateRail
Can’t create Railing. Thickness of Rail or Balusters might be too small. If you don’t want Balusters, specify “None” for Baluster Shape.
Public Property
Static Member
CannotCreateRailGeom
Can’t create geometry for one or more Rails
Public Property
Static Member
CannotCreateRailWarn
Can’t create Railing. Thickness of Rail or Balusters might be too small. If you don’t want Balusters, specify “None” for Baluster Shape.
Public Property
Static Member
CannotCreateRiser
Can’t create geometry for one or more risers.
Public Property
Static Member
CannotCreateSideStringer
Can’t create one or more Side Stringers.
Public Property
Static Member
CannotCreateStairForLevelOverlapping
Some of the multistory stairs couldn’t be created due to the overlapped levels.
Public Property
Static Member
CannotCreateStringers
Can’t create stringers geometry.
Public Property
Static Member
CannotDrawStairs
Can’t make stairs
Public Property
Static Member
CannotDrawStairsError
Can’t make stairs
Public Property
Static Member
CannotEndWithZeroRiser
Can’t end Stairs with Riser because Riser Thickness is too small.
Public Property
Static Member
CannotGenerateFaces
Couldn’t generate surfaces for stairs.
Public Property
Static Member
CannotGenerateFacesError
Couldn’t generate surfaces for stairs.
Public Property
Static Member
CannotGenerateRamp
Couldn’t generate surfaces for ramp.
Public Property
Static Member
CannotGenerateRampError
Couldn’t generate surfaces for ramp.
Public Property
Static Member
CannotMakeLanding
Can’t make landing.
Public Property
Static Member
CannotOffsetBoundary
Can’t create Boundary as an offset of Run Curve
Public Property
Static Member
CannotOffsetRail
Can’t create one or more Rails with desired offset
Public Property
Static Member
CannotPlaceBalusterOffset
Can’t place Balusters and/or Rails with desired offset
Public Property
Static Member
CannotPlaceBalusterPatterns
Can’t place Baluster Patterns
Public Property
Static Member
CannotPlaceRailingOnStringerWarning
Railing is placed on tread because there is no stringer.
Public Property
Static Member
CannotProcessInStairsSketchEditMode
Cannot process when stair(s) in sketch edit mode.
Public Property
Static Member
CannotSplitRailingWithExtensions
Railings with extensions cannot be split.
Public Property
Static Member
ContinuousRailFilletCreationError
Cannot create specified fillet at rail path corner.
Public Property
Static Member
ContinuousRailFilletCreationParallel
Cannot create specified fillet at rail path corner because of the curves are already smoothed.
Public Property
Static Member
ContinuousRailFilletCreationWarning
Cannot create specified fillet at rail path corner.
Public Property
Static Member
ContinuousRailGometryCreationFailure
Cannot create the continuous rail geometry.
Public Property
Static Member
ContinuousRailNotContinuous
The rail is non-continuous.
Public Property
Static Member
ContinuousRailSupportPlacementFailure
Cannot place the supports along the rail path.
Public Property
Static Member
ContinuousRailTransitionFailure
Cannot create specified transition at rail path turn, hand Rail/Top Rail cannot maintain continuous.
Public Property
Static Member
ExtendBelowBaseGreaterThanLandingBaseElevation
Extend Below Base needs to be less than Landing Base Elevation.
Public Property
Static Member
ExtendBelowBaseGreaterThanRunTopElevation
Extend Below Base needs to be less than Run Top Elevation.
Public Property
Static Member
FailToReOrientSketchCurvesFailure
Failed to orient sketch curves.
Public Property
Static Member
HeightOfRunIsTooSmall
Height of run is too small.
Public Property
Static Member
IntermediateLandingHigherThanTopRunFailure
Run is reversed.
Public Property
Static Member
InvalidBalustersPattern
Invalid Balusters Pattern
Public Property
Static Member
InvalidLocationLineJustificationFailure
Modify the location justification to a invalid value.
Public Property
Static Member
InvalidParameters
Stairs run or landing has invalid parameter(s).
Public Property
Static Member
InvalidRailProfile
Profiles for one or more of the Rails are invalid. Make sure that every used Profile is a closed series of non-intersecting Lines.
Public Property
Static Member
InvalidStairsPathFailure
Invalid stairs path provided.
Public Property
Static Member
InvalidStartLevel
The start level and end level for this staircase must be at different elevations.
Public Property
Static Member
InvalidStartLevelRamp
The start level and end level for this ramp must be at different elevations.
Public Property
Static Member
LandingDepthIsLessThanRunWidthWarning
Landing depth is less than run width.
Public Property
Static Member
LandingHeightUnderStairsBottom
Cannot make landing because height of landing is equal or less than to bottom height of the stair.
Public Property
Static Member
LandingShapeHandleOnPinnedRunFailure
Cannot Drag the automatic landing shape handle control because the connected run is pinned.
Public Property
Static Member
MayUnjoinRailAndSupports
Fillet may cause the supports unjoin with the rail.
Public Property
Static Member
MultistoryLevelBelowTopbottomLevel
Multistory top level must be above the stair/ramp top and bottom levels.
Public Property
Static Member
MultistoryLevelBelowTopbottomLevelError
Multistory top level must be above the stair/ramp top and bottom levels.
Public Property
Static Member
MultistoryStairDoesntReach
The multistory stair/ramp could not reach its top level with integral number of flights. Maximum number of flights below the top level is created.
Public Property
Static Member
MultistoryStairsAutomaticLevelLandingsDeleted
Level landings are deleted because the connected stairs have been regenerated.
Public Property
Static Member
MultistoryStairsComponentJoinFailure
Can’t keep elements joined. Avoid converting stairs to skeched-based component in Multistory stairs.
Public Property
Static Member
MultistoryStairsHideTopLevelParameter
You have set the stair’s multistory top level to None, and Revit will remove this parameter, if you want to create a multistory stair, please use Create Multistory Stair feature.
Public Property
Static Member
MultistoryStandardStairBottomEndExceedsOrNotReach
One of the stairs inside multistory stairs bottom ends exceeds or cannot reach the base elevation of the stair.
Public Property
Static Member
MultistoryStandardStairTopEndExceedsOrNotReach
One of the stairs inside multistory stairs top ends exceed or cannot reach the top elevation of the stair.
Public Property
Static Member
MultusegmentRampRiser
Ramp can’t have multisegment Riser.
Public Property
Static Member
MultusegmentRampRiserError
Ramp can’t have multisegment Riser.
Public Property
Static Member
NoCurvesInRailing
Railing Sketch has no Lines.
Public Property
Static Member
NoProfileForRail
Must specify Profiles for every Rail.
Public Property
Static Member
NoRailingsStringer
Railings and Stringers will not be automatically generated due to bad Runs. This message may be incorrect if you have Edited the Sketch and modified some dimensions.
Public Property
Static Member
NoRisersInPureMonolithicStairs
Monolithic Stairs with zero tread thickness can’t have risers
Public Property
Static Member
NoRunsRamp
Ramp has no Runs. Can’t create Ramp.
Public Property
Static Member
NoRunsRampError
Ramp has no Runs. Can’t create Ramp.
Public Property
Static Member
NotALineRiserRamp
Riser line must be a straight line for Ramps.
Public Property
Static Member
NotALineRiserRampError
Riser line must be a straight line for Ramps.
Public Property
Static Member
NotchThicknessIsLargerThanLandingWarning
The notch thickness is larger than landing.
Public Property
Static Member
NotEnoughRisers
Actual Number of Risers is different from Desired Number of Risers. Add/remove Risers or change Desired Number of Risers in Stairs Properties.
Public Property
Static Member
OnlyMonolithicStairs
Tread thickness can’t be zero for non-monolithic stairs
Public Property
Static Member
PartOfRiserLiesOnBoundaryFailure
Part of the riser lies on the boundary is not allowed.
Public Property
Static Member
PathDoesntJoinToBorderRisersFailure
Path doesn’t join to border risers is not allowed.
Public Property
Static Member
RailCurveTooShort
Curve in rail sketch is too short for rail creation and ignored.
Public Property
Static Member
RailingBadOffset
An arc in the railing sketch has a radius that conflicts with the current rail widths and offsets. Please either increase the radius or modify rail profiles and offsets.
Public Property
Static Member
RailingCurvesNotSplitRamp
The slope of this railing will not parallel the ramp at landings. To get a parallel railing, split the railing sketch at the ends of landings.
Public Property
Static Member
RailingCurvesNotSplitStairs
The slope of this railing may not parallel the stairs at runs and landings. To get a parallel railing, split the railing sketch at the ends of landings.
Public Property
Static Member
RailingDoublyConnected
Railings hosted on Stairs must form a single, open, connected line.
Public Property
Static Member
RailingNotConnected
The Railing line must be a single connected Sketch. If you want separate pieces of Railing, create two or more separate Railings.
Public Property
Static Member
RailPathCloseLoopForExtensionWarning
The rail path is closed at the start and end path point for extension creation.
Public Property
Static Member
RailPlacedOutsideOfHost
Railings are placed completely outside the host. It may change the adjustment of the railing to the host and its vertical position.
Public Property
Static Member
RailProfileLowerThanFilletError
Fillet cannot be created between rail segment since the radius is lower than the profile size.
Public Property
Static Member
RailProfileLowerThanFilletFailure
Fillet cannot be created between rail segment since the radius is lower than the profile size.
Public Property
Static Member
RailProfileOpen
Open Profile Loop can’t be used as a Rail Profile
Public Property
Static Member
RailTypeChangeInconsistancyWarningWithResetBtn
Some rail type changes are not consistent with your rail instances customization in this project, you can reset them to make them corresponding with your changes.
Public Property
Static Member
RampDoesntReach
The ramp is not long enough to reach the top constraint. Change the slope or increase the length of the ramp.
Public Property
Static Member
RampDoesntReachOffset
The ramp is not long enough to reach the top constraint plus top offset. Change the slope or increase the length of the ramp.
Public Property
Static Member
RampLandingNotCreated
Beginning of run coincide with the end of previous run. Landing is not created between runs.
Public Property
Static Member
RampRunTooComplex
Ramp Run has complex boundary and may produce unreasonable geometry. Split it into few Runs by inserting Riser Lines at the end of each Run and at the beginning of the next one. If you want to create Ramp with arc an straight section you can do it using a Run tool.
Public Property
Static Member
RampStartHigherThanEnd
The ramp’s base (base level + base offset) must be below its top (top level + top offset).
Public Property
Static Member
RiserCurveTooShort
Riser curve is too short to create nosing on it.
Public Property
Static Member
RiserHeightIsTooSmall
Riser height is too small.
Public Property
Static Member
RiserIntWithBoundaryMoreThanOnceFailure
Riser intersects with boundary more than once.
Public Property
Static Member
RisersAtSameLocation
The highlighted risers have the same location along the boundary line. Please move one of the two risers.
Public Property
Static Member
RiserThicknesssResetToZero
Monolithic Stairs without Treads can’t have Risers. Riser Thickness for Stairs Type was automatically set to zero.
Public Property
Static Member
RunBottomHigherThanTopFailure
The base elevation for the run is higher than the top elevation for the run.
Public Property
Static Member
RunBottomUnderStairsBottomFailure
Run bottom elevation should not be below the stairs bottom elevation.
Public Property
Static Member
RunIsJoiningLandingWithRiserSoNotchDoesNotWorkWarning
Run is joining landing with riser, so notch configuration does not take effect. Try to set run as begin/end with tread to make a notch.
Public Property
Static Member
RunTopLowerThanBottomFailure
The top elevation for the run is lower than the base elevation for the run.
Public Property
Static Member
SpiralRunRadiusTooSmallFailure
The radius value for the run is too small.
Public Property
Static Member
StairIncompleteFailure
Stair element is incomplete, not all components are logic connected.
Public Property
Static Member
StairsActualRiserHeightGreaterThanMaximumFailure
Computed actual riser height of stairs is greater than maximum riser height defined in stairs type.
Public Property
Static Member
StairsActualRunWidthLessThanMinimumFailure
Actual run width is less than minimum run width defined in stairs type.
Public Property
Static Member
StairsActualTreadDepthLessThanMinimumFailure
Computed actual tread depth of stairs is less than minimum tread depth defined in stairs type.
Public Property
Static Member
StairsAlreadyAttachedToCurrentLevel
Mutistory Stairs already have a Stair attaching to this level.
Public Property
Static Member
StairsAreUpdatedDueToLevelHeightChange
Stair component(s) in the multistory stair are updated due to the level height changes.
Public Property
Static Member
StairsAutomaticLandingLayoutFailure
Fail to generate the automatic landing layout
Public Property
Static Member
StairsAutomaticLandingLayoutWarn
Fail to generate the automatic landing layout
Public Property
Static Member
StairsBottomEndExceedsOrNotReachWarning
Stair bottom end exceeds or cannot reach the base elevation of the stair. Add/remove risers at the bottom end or change base elevation settings in Stair Properties.
Public Property
Static Member
StairsCannotExtendToFloorStructureLayerWarning
Stairs cannot extend to floor structure layer.
Public Property
Static Member
StairsCommonRunGenerateLayoutFailure
Fail to get base line thus fail to generate run layout
Public Property
Static Member
StairsComponentJoinFailure
Can’t keep elements joined.
Public Property
Static Member
StairsCrossingRisersDisallowedFailure
Crossing risers are not allowed
Public Property
Static Member
StairsGenericFailure
Stairs generic failure
Public Property
Static Member
StairsGenericTransformFailure
Cannot change base elevation of Stairs
Public Property
Static Member
StairsIllegalDesiredNumRisers
Desired Number of Risers is too small. Computed Actual Riser Height is greater than Maximum Riser Height allowed by type.
Public Property
Static Member
StairsInMultistoryExceedTopConstraint
Stairs in MultistoryStairs after adjusting still exceed the top constraint.
Public Property
Static Member
StairsOnlySingleBoundaryHasRiserWithBothEndsOnBoundaryFailure
Only single boundary case may have riser with its both ends on boundary.
Public Property
Static Member
StairsOtherThan2IntsByRiserAndBoundaryFailure
More than 2 intersection points between riser segment and boundary encountered
Public Property
Static Member
StairsPathPositionResetWarning
The stairs path doesn’t intersect with riser lines.
Public Property
Static Member
StairsRunRunJoinNotAllowedFailure
Run-Run join is not allowed of they have same “Start With Riser”/“End With Riser” configuration at the joined end.
Public Property
Static Member
StairsStartHigherThanEnd
The stairs’ base (Base Level + Base Offset) must be below its top (Top Level + Top Offset).
Public Property
Static Member
StairsStringerCannotBeCreated
The stairs stringer cannot be created.
Public Property
Static Member
StairsSubElementsNotConnectedWarning
Stair sub-elements are not connected
Public Property
Static Member
StairsSupportOverlapFailure
Some supports overlap with others
Public Property
Static Member
StairsSupportTooShort
A short support is being created.
Public Property
Static Member
StairsTopEndExceedsOrNotReachWarning
Stair top end exceeds or cannot reach the top elevation of the stair. Add/remove risers at the top end or change top elevation settings in Stair Properties.
Public Property
Static Member
StairsTopLowerThanBaseFailure
The top of the Stair is lower than the base of the Stair
Public Property
Static Member
StairStringerCantOffset
Inside stringer could not be created because of insufficient space. Please disable the inside stringer or decrease its width.
Public Property
Static Member
StairsWinderGenLayoutFailure
Fail to generate run layout and then cannot make winder run
Public Property
Static Member
StairsWinderInvalidParamsFailure
Cannot create the winder run because some values for the instance properties cannot be satisfied.
Public Property
Static Member
StairsZeroDesiredRisers
The number of desired risers for a staircase cannot be 0.
Public Property
Static Member
StringerCurvesNotSplitStairs
The slope of stringer may not parallel runs and landings. To get a parallel stringer, split boundary lines at the ends of landings.
Public Property
Static Member
StringerCurveTooShort
A piece of boundary is too short to create stringer on it.
Public Property
Static Member
TooShortCurveDowngradeGeometry
Curve is too short and may downgrade the geometry.
Public Property
Static Member
TreadDepthBelowMin
The Actual Tread Depth for one or more Stairs violates the Minimum Depth set in the type.
Public Property
Static Member
TreadDepthFailsEq
The actual tread depth and riser height for one or more stairs of this type violates the stair equation.
Public Property
Static Member
TreadDepthTooBigFailure
The tread depth is too large for the spiral run.
Public Property
Static Member
TreadFrontProfileInvalid
This profile cannot be used for the front of treads. Please choose a profile composed of a closed loop of lines with exactly one lines coincident with the y-axis. This lines will define the connection of this profile to the tread.
Public Property
Static Member
UnableToCreateMultistoryStairs
Unable to create Multistory stairs.
Public Property
Static Member
UnexpectedCurveIntersectionFailure
Computing curve intersection and find the invalid result.
Public Property
Static Member
WinderFilletRadiusTooLargeFailure
The value for Fillet Radius is too large to satisfy the Minimum Inside Width value.
Public Property
Static Member
WinderFirstLegTooShortOrRunWidthTooGreatFailure
The first leg of winder run is too short or the runwidth is too great.
Public Property
Static Member
WinderGenericError
Cannot make winder.
Public Property
Static Member
WinderLegIsTooShortFailure
A winder leg is too short.
Public Property
Static Member
WinderLegsAngleTooGreatOrRunWidthTooSmallFailure
The angle between two consecutive legs are too great or the runwidth is too small.
Public Property
Static Member
WinderLegTooShortOrRunWidthTooGreatFailure
One leg of the winder run is too small or the runwidth is too great.
Public Property
Static Member
WinderMinWidthTooLargeFailure
The value for Minimum Width on Inside Boundary is too large.
Public Property
Static Member
WinderMinWidthTooLargeForParallelTreadsFailure
The value for Minimum Width on Inside Boundary is too large to satisfy the number of Parallel Treads at the Start or End as specified in the Run Instance properties.
Public Property
Static Member
WinderParallelLegsFailure
Two consecutive legs are parallel.
Public Property
Static Member
WinderParallelTreadsNumberFailure
Cannot satisfy the number of Parallel Treads at the Start or End as specified in the Run Instance properties
Public Property
Static Member
WinderRunCreationFailure
The relationship between the current values of Actual Run Width, Minimum Width at Inside Boundary, and Parallel Treads at Start or End does not support the creation of the winder run.
Public Property
Static Member
WinderRunInsideMinTreadDepthFailure
Please enter a positive value less than Actual Tread Depth on Stair Path (%Actual Tread Depth%).
Public Property
Static Member
WinderRunInsideWalklineOffsetFailure
Please enter a value between 0 and half of Actual Run Width (%1/2 Actual Run Width%).
Public Property
Static Member
WinderRunWidthLessThan2TimesMinWidthFailure
The value for Minimum Width on Inside Boundary is too large to satisfy the number of Parallel Treads at the Start or End as specified in the Run Instance properties.
Public Property
Static Member
WinderRunWidthLessThanWalkLineOffsetFailure
The value for Run Width is less than two times of value of the inside walkline offset.
Public Property
Static Member
WinderRunWidthOrMinWidthOrTooGreatParallelTreadsFailure
The parameter runwidth is great or the parameter min width at inside boundary is too great, or number of parallel treads at both ends is too great.
Public Property
Static Member
WinderRunWidthOrMinWidthOrTooShortFailure
The parameter runwidth is too great or the parameter min width at inside boundary is too great, or one leg of winder run is too short.
Public Property
Static Member
WinderSecondLegTooShortOrRunwidthTooGreatFailure
The second leg of winder run is too short or the runwidth is too great.
Public Property
Static Member
WinderStraightStepsNumberFailure
The current layout cannot allow the specified number of treads. Increase the length of the run leg in the model or reduce the value for Parallel Treads at Start or Parallel Treads at End.
Public Property
Static Member
WinderThirdLegTooShortOrRunWidthTooGreatFailure
The third leg of winder run is too short or the runwidth is too great.
Public Property
Static Member
WinderTooManyEndParallelTreadsOrRunWidthFailure
The number of parallel treads at end is too great or the run width is too great.
Public Property
Static Member
WinderTooManyParallelTreadsAtEndFailure
The number of parallel treads at end is too great.
Public Property
Static Member
WinderTooManyParallelTreadsAtHeadFailure
The number of parallel treads at start is too great.
Public Property
Static Member
WinderTooManyStartParallelTreadsOrRunWidthFailure
The number of parallel treads at start is too great or the run width is too great.