BuiltInFailures.MEPFabricationFailures

Public Class

Failures about MEP fabrication.

Inheritance Hierarchy

System.Object
Autodesk.Revit.DB.BuiltInFailures.MEPFabricationFailures

Assembly: RevitAPI (in RevitAPI.dll) Version: 25.0.0.0 (25.0.0.0)

Syntax

public static class MEPFabricationFailures

The BuiltInFailures.MEPFabricationFailures type exposes the following members.

Properties

Name

Description

Public Property
Static Member

AdditionalPartNotLoaded

An additional part was not loaded.

Public Property
Static Member

CannotConvertFlexPipeToPart

Cannot convert flex pipe to fabrication part.

Public Property
Static Member

CannotMatchFabricationHangerSizeToHost

The hanger cannot be re-sized to match the re-sized host.

Public Property
Static Member

FabDbChangeConn

Fabrication Database changes altered connectivity

Public Property
Static Member

FabDbOpenJobConn

Fabrication job imported had bad connectivity

Public Property
Static Member

FabDbSwapOut

Fabrication Database reload could not swap out for newer parts.

Public Property
Static Member

FabricationConfigurationCorrupted

It looks that the Fabrication Configuration %1!s! was corrupted, please check it at %2!s!.

Public Property
Static Member

FabricationHangerCannotBeSloped

A hanger cannot be sloped or placed on a sloped element.

Public Property
Static Member

FabricationHangerHostNotFound

The hanger will disconnect because we can’t find the suitable host.

Public Property
Static Member

FabricationHangerNotConnectToHost

Fabrication Hanger didn’t connect to the %s host.

Public Property
Static Member

FabricationHangerOutOfHost

The hanger is out of its host and will be disconnected.

Public Property
Static Member

FabricationHangerSizeNotMatch

The hanger size does not match the size of the host, so it can not be connected.

Public Property
Static Member

FabricationOutOfSizeCondition

The fabrication part size is not within the correct size range for the service button condition.

Public Property
Static Member

FabricationOverSizedCheck

Fabrication part is too large to fit on the sheet metal. Replace the part with multiple smaller parts, or notify the CAM operator.

Public Property
Static Member

FabricationPartBadConnectionAlignmentWarning

The connection invalid due to the connector are not aligned and/or this is a gap between the connectors.

Public Property
Static Member

FabricationPartBadConnectionConnectivityWarning

The connection invalid due to connection types associated to the connectors are not compatible.

Public Property
Static Member

FabricationPartBadConnectionSizeWarning

The connection invalid due to connectors sizes are not the same.

Public Property
Static Member

FabricationPartCannotBeMirrored

Public Property
Static Member

FabricationPartCannotChangeServiceSizeWarning

The selected fitting(s) cannot successfully change service or change size. You must disconnect the connections on the fitting(s) and try again.

Public Property
Static Member

FabricationPartCannotChangeSlopeError

The connected fitting(s) cannot successfully change to the new slope value. You may try to disconnect the connections on the fitting(s) and try again.

Public Property
Static Member

FabricationPartCannotChangeTypeBadDimError

The selected fitting(s) cannot successfully change the type. The newly selected fabrication part may have badly configured dimensions or be constrained due to connected fitting(s). You may try to disconnect the connections on the fitting(s) and try again.

Public Property
Static Member

FabricationPartCannotChangeTypeBadDimUnConnError

The selected fitting(s) cannot successfully change the type. The newly selected fabrication part may have badly configured dimensions, resulting in bad geometry.

Public Property
Static Member

FabricationPartCannotChangeTypeError

The selected fitting(s) cannot successfully change the type. You must disconnect the connections on the fitting(s) and try again.

Public Property
Static Member

FabricationPartCannotChangeTypeIncompatError

The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type either has no material or has badly configured dimensions, resulting in bad geometry. You may try to disconnect the connections on the fitting(s) and try again.

Public Property
Static Member

FabricationPartCannotChangeTypeIncompatUnConnError

The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type either has no material or has badly configured dimensions, resulting in bad geometry.

Public Property
Static Member

FabricationPartCannotChangeTypeMisalignedError

The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type has a problem with the angle dimension of the current fitting(s), resulting in bad geometry. You may try to disconnect the connections on the fitting(s) and try again.

Public Property
Static Member

FabricationPartCannotChangeTypeMisalignedUnConnError

The selected fitting(s) cannot successfully change the type. The newly selected fabrication part type has a problem with the angle dimension of the current fitting(s), resulting in bad geometry.

Public Property
Static Member

FabricationPartCannotChangeTypeUnConnError

The selected fitting(s) cannot successfully change the type.

Public Property
Static Member

FabricationPartCannotChangeTypeWarning

The selected fitting(s) cannot maintain connections to existing fabrication parts due to size, direction or angle differences. You must manually reconnect the open connections.

Public Property
Static Member

FabricationPartExceededAngleFlexToleranceWarning

The angle flex is greater than the maximum angle flex tolerance defined by the fabrication part. Connections with this part may not be properly aligned and may appear to be skewed.

Public Property
Static Member

FabricationPartExcludedPartWarning

There were fabrication parts needed to the make the connection that were excluded from the fabrication service causing the connection to fail. You may try to inlcude these fitting(s) and try again.

Public Property
Static Member

FabricationPartFitFailure

Fabrication Part Fitting Failed to Fit

Public Property
Static Member

FabricationPartFitFailWarning

Fabrication Part Fitting Failed to Fit

Public Property
Static Member

FabricationPartHasInvalidGeometry

The fabrication part either has no material or has badly configured dimensions, resulting in bad geometry.

Public Property
Static Member

FabricationPartInvalidConnection

Fabrication Part connection invalid and could not be automatically coupled.

Public Property
Static Member

FabricationPartInvalidSpecification

The part specification is invalid.

Public Property
Static Member

FabricationPartNoPartTypeFound

There are no fabrication part types found for the current Configuration and Service. Please select settings and reload the service to create the fabrication part types.

Public Property
Static Member

FabricationPartNotAttachedToStraight

The part must be attached to straight.

Public Property
Static Member

FabricationPartOptimizeInvalidConnection

No available couplings to connect standard lengths for this instance of straight.

Public Property
Static Member

FabricationRodDetachFromHangerError

The rod need to be detached from hanger.

Public Property
Static Member

FabricationRodsConnectionChangedWarning

The structural component that the hanger is attached to has changed to a different element.

Public Property
Static Member

FabricationRodsDisconnectedError

The hanger rod was disconnected because there is no structural component above.

Public Property
Static Member

FabricationRodsDisconnectedWarning

The hanger rod was disconnected because there is no structural component above.

Public Property
Static Member

FabricationServiceMismatch

Attempting to connect fabrication parts from different services.

Public Property
Static Member

FabricationStraigtLengthOversized

Fabrication straight exceeds the standard length. Use the Optimize Length command to adjust the length.

Public Property
Static Member

FixedFabricationPartNotChangeLength

Failed to change length of fixed part.

Public Property
Static Member

GroupedFabricationPartNotReposition

Failed to reposition part.

Public Property
Static Member

HangerProfileNotMatchWithHost

The defined hanger profile does not match with the host.

Public Property
Static Member

HangerWidthOutOfRange

The hanger width is too large to show.

Public Property
Static Member

InvalidConnectionsHaveBeenDisconnected

Invalid connections have been disconnected. Please reconnect them manually or use different fittings.

Public Property
Static Member

InvalidSelectionThereCannotBeOpenConnectors

Invalid selection there cannot be any open connectors for the design to fabrication part tool.

Public Property
Static Member

NoStructuralHostToAttachWarning

There is no structural component to attach the hanger rod to.

Public Property
Static Member

NotAllPartsWereConvertedUnsuportedFittingOffsets

Not all parts were converted. Eccentric transitions and taps that have offsets from the center line are unsupported and cannot be converted.

Public Property
Static Member

PinnedFabricationPartNotChangeExtension

Failed to change extension of part.

Public Property
Static Member

PinnedFabricationPartNotReposition

Failed to reposition part.

Public Property
Static Member

PlaceCutinFittingFailed

Failed to insert part.

Public Property
Static Member

SizeNotAvailableInFabricationService

Sizes:%1!s! in system %2!s! are not available in fabrication service:%3!s!, All available sizes are:\n%4!s!.

Public Property
Static Member

UneditableFabricationPartNotReposition

Failed to reposition part.